Skip to main content

Diagnose Crescent-Style Ice Maker Components with Multimeter — Test the Ice Maker Motor and Thermostat

Beginner4 hours

Part of project

Ice Maker Repair · Step 5 of 7

Helpful?

In this video

For crescent-style ice makers, several components can fail. First, remove the ice maker's cover to expose the control module. Set your digital multimeter to ohms (Ω) mode. 1. **Test the Mold Heater**: Place one probe into the 'L' hole and the other into the 'H' hole. A healthy mold heater should read approximately 72 ohms. If the reading is 'OL' (Overload) or significantly different, the heater is faulty and needs replacement. 2. **Test the Motor**: Place one probe into the 'L' hole and the other into the 'M' hole. The motor should register a reading between 4400 and 8800 ohms. An 'OL' reading indicates a failed motor. 3. **Test the External Water Valve Solenoid**: Place one probe into the 'V' hole and the other into the 'N' hole. This test checks the external water valve solenoid, which should show approximately 300 ohms. An 'OL' reading means the solenoid has failed. 4. **Test the Mold Thermostat (Cold)**: Place probes into the 'T' and 'H' holes. When the ice maker is below 15°F, the thermostat should show continuity (a low resistance reading, typically near 0 ohms). If it does not, the thermostat is faulty. 5. **Test the Mold Thermostat (Warm)**: Allow the ice maker to warm up above 15°F. Once warm, retest the 'T' and 'H' holes. The thermostat should now show no continuity ('OL' reading). If it still shows continuity, the thermostat is faulty.

21.2K views270

FAQs

What are the most critical safety steps I must take before starting an ice maker repair?

Always prioritize safety by first disconnecting power to your refrigerator at the circuit breaker. Next, locate and turn off the water supply valve connected to the ice maker. Double-check that both power and water are fully off before touching any components to prevent electrical shock or water damage.

Are all the listed tools, especially the multimeter and pliers, truly necessary for this beginner-level repair?

Yes, a multimeter is essential for accurately diagnosing electrical issues by testing components like the motor and thermostat. Pliers and various screwdrivers are fundamental for disassembly and reassembly. While you might not install a new circuit breaker, knowing where it is to safely cut power is critical for this repair.

My ice maker isn't producing any ice at all. What's the most common problem I should look for first?

If there's no ice, begin by checking the water inlet valve for clogs or signs of malfunction, and ensure the water supply line isn't frozen, kinked, or disconnected. If water flow is confirmed, the issue could be with the ice maker's motor or thermostat, which you can test with a multimeter as outlined in the steps.

Is the 4-hour estimated time realistic for a beginner, and what might cause the repair to take longer?

Four hours is a reasonable estimate for a beginner, allowing time for careful diagnosis, part acquisition, and reassembly. The repair might take longer if you encounter seized screws, need to perform extensive cleaning to clear blockages, or have difficulty identifying or sourcing the correct replacement parts for your specific appliance model.

Transcript
Hide

If the ice factory is not producing ice, it could be that it has failed. The most common phases are the thermostat of the mold, the crankshafts, or the engine and the interruptors inside the control module. If some of these components have failed, the ice factory will stop producing ice. In general, when it fails, ice factory already has an age in which to change it completely could be the best option, but if you want to make a more deep diagnosis, depending on the design, maybe you can buy individual pieces. Throughout the years, many ice factory styles were used, here who are two very popular. As we mentioned before, this is the medium-sized steel style and this is the flexible bandage. Here are the parts of the medium-sized steel model. You have the control of the ice factory, which includes the contact of the luggage, the engine of the raster and the ingranage. The thermostat of the mold and the calentator of the mold are in the own ice mold. We are going to show you how to test the popular design of Gwyrpun. There are other ice factories that are similar, but they have their own test procedures. We are going to use a multimeter to test the pieces. So we are going to put our medium-sized steel. Our medium detects automatically the screws that come in, but it can be necessary to adjust your medium-sized steel to read the correct level of the screw. First, remove the lid. Then, to test the calentator of the mold, put a probe in the marked holes with the ice and ice. It should mark around 72 screws. Then, to check the engine, put the probe in the ice holes and ice. The medium must mark between 4,400 and 8,800 screws. Put the probe in the holes above and ice, to check the heat of the external air bubble. It must mark around 300 screws. Remember, any of the reading can vary a little, but if they are completely out of range or you don't have any reading, the piece will have to be replaced. Finally, to check the thermostat of the mold, we need to see if it has continuity. Here we are not looking for a specific value. We just want to see if the medium mark is something. So, put the probe in the holes of the H and H. The mid of the thermostat, when it is below 15 degrees Fahrenheit, it must have continuity when it is cold. If it does not have it, then it must be replaced. Then, let the thermostat heat up, so that it is above 15 degrees. If you don't want to disconnect the freezer to let it heat up, you may want to remove the ice machine to be able to test it.…

Auto-generated transcript. May contain errors.