Skip to main content

Connect to Main Electrical Panel and Disconnect Switch — Electrical Wiring and Connections

Intermediate2 mins

Part of project

Residential Solar Panel System · Step 5 of 7

Helpful?

In this video

Connect the solar system's electrical output to the house's main electrical panel. This involves routing the combined AC power wires from the roof junction box through the wall (usually by drilling a hole in the panel to the outside) to an external solar disconnect switch and a combiner box (if applicable). This external disconnect switch, often a "knife blade switch", allows all power from the solar panels to be safely cut off from the house and the grid, which is a critical safety feature for utility workers. From the disconnect, thick gauge wires are routed back into the main electrical panel, connecting to dedicated breakers (e.g., 20-amp breakers for each string). Remember to connect the ground wire to the grounding bar in the panel. Ensure all connections adhere to local electrical codes and the custom plan set.

4.3M views112.5K
JerryRigEverything

9.9M subscribers

View Channel

FAQs

What are the most critical safety precautions for a DIY solar panel installation?

Working with solar panels involves high DC voltage, and connecting to your home's electrical system involves high AC voltage. Always de-energize circuits, use insulated tools, and wear appropriate PPE. However, due to the inherent risks of working with live electrical systems and grid connections, it is strongly recommended to hire a licensed professional.

What permits and inspections are typically required for a residential solar system?

Most jurisdictions require building permits for structural mounting and electrical permits for wiring. You'll also likely need a final inspection from both the building department and your utility company before commissioning the system. Check with your local authority having jurisdiction (AHJ) early in the planning phase.

How do I ensure my roof can support the weight of solar panels?

Before installing any mounting system, a structural assessment of your roof is crucial. This often requires an engineer's review to ensure the existing rafters and sheathing can safely bear the additional load of the panels, snow, and wind. Do not proceed without this assessment.

What are common mistakes DIYers make when installing solar panels?

Common mistakes include improper roof flashing leading to leaks, incorrect wiring causing electrical hazards or system failure, inadequate grounding, and failing to comply with local codes. These errors can be dangerous and costly to fix, emphasizing the need for professional expertise.

Transcript
Hide

the ground all right so let me tell you what's going on electrically here for a second we actually haven't connected the wires yet this is the panel that's powering the house we're in right now and we've drilled a hole through the panel to the outside and then these two boxes out here that we just installed are going to take the power from the solar panels on the roof bring them into this box combine all the panels and then head over here to the solar disconnect which can actually disconnect all of the power from the solar panels heading into the house it's a safety thing when working with the wires in the electrical part of the solar system remember to one follow local cold nb follow your plan set it'll explain everything you need to know so we have the larger array up here the smaller array down here at the bottom and they're all connected in this joiner box here in the center all the wires from the roof and this side panel over here feed into this and you can see these ground wires these copper wires that were attached to the rails all those are heading down to the breaker box which i'll show you in a second now we can tuck all these wires inside the box and close it up so down here in the breaker box this is what's accepting the two strings that i have each of the strings has their own 20 amp breaker black and red go in the bottom and the ground goes over here on the side so remember there's two kinds of solar system there's grid tied and off grid we installed a grid tied system here which means that the solar panels need to sense the grid before they start supplying power to my house if those micro inverters up top don't sense power from the grid they're going to stay off so i can touch these wires all i want because we're not attached to the grid yet if you want an off-grid system there's a few other components you need to install and maybe i'll make a video about that later but this is all about grid tied if you do want to use your solar panels when the city power goes out you would need a battery or a generator it's pretty cool that all of those solar panels just come down into these six wires makes it pretty simple and now we're gonna connect that breaker panel to the solar disconnect with this thicker gauge wire and it should just uh go through the hole and we can wire it up now we're gonna take the same thickness of wire and push it through to the breaker panel on the other side of the wall so this is still not…

Auto-generated transcript. May contain errors.